آمپلی فایر Crown I-T8000

Features:

• Compact, reliable and ultra powerful amp
• Stereo @ 8 ohms: 2100 watts
• Stereo @ 4 ohms: 4000 watts
• Stereo @ 2 ohms: 3500 watts
• Bridged mono @ 8 ohms: 8000 watts
• Bridged mono @ 4 ohms: 7000 watts
• Frequency response (at 1 watt, 20Hz - 20kHz): ?0.25dB
• Signal to noise ratio below rated 8 ohm power, A-weighted: >105 dB
• Total harmonic distortion (THD) at full rated power: < 0.35%
• Damping factor (20Hz - 100Hz): > 5000
• Common mode rejection (CMR) (20Hz - 1kHz): > 50 dB
• Input impedance (nominal): 10 kilohms balanced, 5 kilohms unbalanced
• Maximum input level: 15dBu or 22 dBu, depending on input sensitivity
• Latency (analog, digital inputs): 1.05 mS analog, 2.29 mS digital (44.1kHz)
• A/D, D/A converters: 24-bit, 96kHz Cirrus Logic
• Digital input: AES/EBU, 16-24-bit, 32-48kHz. Onboard sample rate converter Optional CobraNet input coming soon
• Network: Onboard TCP/IQ, compatible with standard 100MB ethernet hardware
• DSP: 24-bit conversion with 32-bit, floating-point DSP processing. Bypass mode available. Has 64 assignable filters with 9 different filter types. Includes all-pass filters, over 2 seconds of delay available per channel, and dual uncorrelated-noise and sine-wave generators
• Load supervision: Monitors the average impedance on the output of the amplifier. Attenuators: Speed sensitive, continuously variable rotary encoder, 0.5 dB steps, range 0 to ?100 dB
• Load impedance: stereo: 1/2/4/8/16 ohms; bridge mono: 2/4/8 ohms
• Voltage gain (referenced to 8 ohm rated output): Adjustable in 0.1V steps from 1.4V to 7.5V (39.3 dB gain to 24.7 dB gain)
• Required AC mains: Universal AC input, 100-240 VAC, 50/60 Hz (?15%)
• Maximum AC mains voltage: 277 VAC
• AC line connector: five cordsets supplied with amplifier (USA, UK,
• Europe, Australia, India)
• Front panel controls and indicators: bridge mode, ready, signal, clip, thermal, fault, data, power, AC mains present
• Glowing blue screen and controls: these let the user adjust the amplifier's attenuation and muting, configure the amp, set up error monitoring (such as temperature and load supervision) and recall DSP presets. The presets allow the user to quickly reconfigure the amp for various applications.
• LCD control screen: integrated LCD with white LED backlight, controls amplifier setup and operation
• Attenuator: controls amplifier attenuators in 0.5 dB steps
• Main menu (amplifier setup): bridge, input Y, recall preset, LCD contrast, input sensitivity
• Advanced menu: attenuator limit, attenuator link, clip limiter, output voltage limiter, output power limiter, pink noise generator, monitor, input, max input, power-up options
• Power Cord Connector: Standard 20 amp IEC inlet
• Switch/circuit breaker: resets the circuit breaker that protects the
• power supply
• Output connectors: 2 Speakon, 2 binding posts, 2 male XLR passive analog loop through, XLR active/re-clocked AES/EBU digital loop through
• Analog input connectors: 3-pin female XLR connector for each channel
• Digital input connector: 3-pin female XLR connector that accepts a digital signal in the AES/EBU format
• Ethernet connector: accepts an RJ45 connector for IQ TCP/IQ networking and optional CobraNet transport from a standard network cable. Built into the connector is a yellow LINK ACT indicator that shows network activity, and a green 100MB indicator that shows a 100MB network connection
• Cooling: dual-zone, microprocessor controlled, continuously variable
• speed, front-to-back airflow
• Front Panel: Cast aluminum with integrated handles.
• Included accessories: rear rack ears with integral EZ-Rack pin, cable retention bar, rack screws, operation manual, power cords, foam air filter
• Size: 19"w x 3.5"h x 16.2"d. Wt. 28 lbs.